Discussion:
[9fans] I need some EDID
(too old to reply)
ron minnich
2012-10-22 19:22:06 UTC
Permalink
so, if any of you have X11 running, and could do this:
xrandr --verbose

and send the output to me, subject
EDID

I would NOT be forever in your debt, and I will NOT put your name in
lights, but I would appreciate it :-)

ron
b***@bellsouth.net
2012-10-23 04:11:52 UTC
Permalink
Post by ron minnich
xrandr --verbose
From an HP laptop running FreeBSD:

Screen 0: minimum 320 x 200, current 1280 x 800, maximum 1280 x 1280
VGA disconnected (normal left inverted right x axis y axis)
Identifier: 0x41
Timestamp: 81746
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
LVDS connected 1280x800+0+0 (0x44) normal (normal left inverted right x axis y axis) 304mm x 190mm
Identifier: 0x42
Timestamp: 81746
Subpixel: horizontal rgb
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 1
CRTCs: 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff00320c320100000000
00120103801e13780ab3859558538a28
25505400000001010101010101010101
010101010101121b007d502016303020
360030be100000180000000000000000
00000000000000000000000000fe004c
475068696c6970734c43440a000000fe
004c503134315758332d544c4e3200a7
PANEL_FITTING: full_aspect
supported: center full_aspect full
BACKLIGHT_CONTROL: combination
supported: native legacy combination kernel
BACKLIGHT: 0 (0x00000000) range: (0,0)
1280x800 (0x44) 69.3MHz -HSync -VSync *current +preferred
h: width 1280 start 1328 end 1360 total 1405 skew 0 clock 49.3KHz
v: height 800 start 803 end 809 total 822 clock 60.0Hz
1024x768 (0x45) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
800x600 (0x46) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
640x480 (0x47) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
HDMI-1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x43
Timestamp: 81746
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BROADCAST_RGB: 0 (0x00000000) range: (0,1)
b***@bellsouth.net
2012-10-23 04:17:58 UTC
Permalink
Post by ron minnich
xrandr --verbose
Oops. Sorry about that all.

BLS
Derek Carter (aka goozbach)
2012-10-23 04:33:38 UTC
Permalink
Post by b***@bellsouth.net
so, if any of you have X11 running, and could do this: xrandr
--verbose
Oops. Sorry about that all.
BLS
looks like I did the same thing. Sorry.

- --
Derek
aka goozbach
Derek Carter (aka goozbach)
2012-10-23 04:27:33 UTC
Permalink
so, if any of you have X11 running, and could do this: xrandr
--verbose
and send the output to me, subject EDID
I would NOT be forever in your debt, and I will NOT put your name
in lights, but I would appreciate it :-)
ron
Macbook Pro 15" 2012 model

$ xrandr --verbose
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 640 x 480, current 1680 x 1028, maximum 1680 x 1050
default connected 1680x1028+0+0 (0x21d) normal (normal) 0mm x 0mm
Identifier: 0x210
Timestamp: -1982855953
Subpixel: unknown
Clones:
CRTC: 0
CRTCs: 0
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
1680x1050 (0x211) 105.8MHz
h: width 1680 start 0 end 0 total 1680 skew 0 clock
63.0KHz
v: height 1050 start 0 end 0 total 1050 clock
60.0Hz
1680x1050 (0x212) 3.5MHz
h: width 1680 start 0 end 0 total 1680 skew 0 clock
2.1KHz
v: height 1050 start 0 end 0 total 1050 clock
2.0Hz
1440x852 (0x213) 73.6MHz
h: width 1440 start 0 end 0 total 1440 skew 0 clock
51.1KHz
v: height 852 start 0 end 0 total 852 clock
60.0Hz
1280x1024 (0x214) 78.6MHz
h: width 1280 start 0 end 0 total 1280 skew 0 clock
61.4KHz
v: height 1024 start 0 end 0 total 1024 clock
60.0Hz
1152x720 (0x215) 49.8MHz
h: width 1152 start 0 end 0 total 1152 skew 0 clock
43.2KHz
v: height 720 start 0 end 0 total 720 clock
60.0Hz
1024x768 (0x216) 47.2MHz
h: width 1024 start 0 end 0 total 1024 skew 0 clock
46.1KHz
v: height 768 start 0 end 0 total 768 clock
60.0Hz
1024x640 (0x217) 39.3MHz
h: width 1024 start 0 end 0 total 1024 skew 0 clock
38.4KHz
v: height 640 start 0 end 0 total 640 clock
60.0Hz
1280x800 (0x218) 61.4MHz
h: width 1280 start 0 end 0 total 1280 skew 0 clock
48.0KHz
v: height 800 start 0 end 0 total 800 clock
60.0Hz
800x600 (0x219) 28.8MHz
h: width 800 start 0 end 0 total 800 skew 0 clock
36.0KHz
v: height 600 start 0 end 0 total 600 clock
60.0Hz
800x500 (0x21a) 24.0MHz
h: width 800 start 0 end 0 total 800 skew 0 clock
30.0KHz
v: height 500 start 0 end 0 total 500 clock
60.0Hz
640x480 (0x21b) 18.4MHz
h: width 640 start 0 end 0 total 640 skew 0 clock
28.8KHz
v: height 480 start 0 end 0 total 480 clock
60.0Hz
720x480 (0x21c) 20.7MHz
h: width 720 start 0 end 0 total 720 skew 0 clock
28.8KHz
v: height 480 start 0 end 0 total 480 clock
60.0Hz
1680x1028 (0x21d) 1.7MHz *current
h: width 1680 start 0 end 0 total 1680 skew 0 clock
1.0KHz
v: height 1028 start 0 end 0 total 1028 clock
1.0Hz

- --
Derek
aka goozbach
Jean-Pierre Messager
2012-10-23 09:41:25 UTC
Permalink
Post by ron minnich
xrandr --verbose
and send the output to me, subject
EDID
I would NOT be forever in your debt, and I will NOT put your name in
lights, but I would appreciate it :-)
ron
GNU/Linux - Xorg - Monitor: Dell ST2410b

$ xrandr --verbose
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192
VGA1 connected 1920x1080+0+0 (0x42) normal (normal left inverted right x
axis y axis) 531mm x 299mm
Identifier: 0x41
Timestamp: 16823
Subpixel: unknown
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff0010ac5ba055524630
141401030e351e78eeee91a3544c9926
0f5054a54b00714f8180d1c001010101
010101010101023a801871382d40582c
4500132b2100001e000000ff00573138
3952303544304652550a000000fc0044
454c4c205354323431300a20000000fd
00324c1e5311000a20202020202000d9
1920x1080 (0x42) 148.5MHz +HSync +VSync *current +preferred
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock
67.5KHz
v: height 1080 start 1084 end 1089 total 1125 clock 60.0Hz
1280x1024 (0x43) 135.0MHz +HSync +VSync
h: width 1280 start 1296 end 1440 total 1688 skew 0 clock
80.0KHz
v: height 1024 start 1025 end 1028 total 1066 clock 75.0Hz
1280x1024 (0x44) 108.0MHz +HSync +VSync
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock
64.0KHz
v: height 1024 start 1025 end 1028 total 1066 clock 60.0Hz
1152x864 (0x45) 108.0MHz +HSync +VSync
h: width 1152 start 1216 end 1344 total 1600 skew 0 clock
67.5KHz
v: height 864 start 865 end 868 total 900 clock 75.0Hz
1024x768 (0x46) 78.8MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock
60.1KHz
v: height 768 start 769 end 772 total 800 clock 75.1Hz
1024x768 (0x47) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock
48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
800x600 (0x48) 49.5MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock
46.9KHz
v: height 600 start 601 end 604 total 625 clock 75.0Hz
800x600 (0x49) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock
37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
640x480 (0x4a) 31.5MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock
37.5KHz
v: height 480 start 481 end 484 total 500 clock 75.0Hz
640x480 (0x4b) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock
31.5KHz
v: height 480 start 490 end 492 total 525 clock 60.0Hz
720x400 (0x4c) 28.3MHz -HSync +VSync
h: width 720 start 738 end 846 total 900 skew 0 clock
31.5KHz
v: height 400 start 412 end 414 total 449 clock 70.1Hz
David Leimbach
2012-10-23 14:22:59 UTC
Permalink
Big Damn HP monitor (ZR30w)

Screen 0: minimum 320 x 200, current 2560 x 1600, maximum 8192 x 8192
VGA1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x41
Timestamp: 19460
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
HDMI1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x42
Timestamp: 19460
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
force_audio: 0 (0x00000000) range: (-1,1)
DP1 connected 2560x1600+0+0 (0x44) normal (normal left inverted right x
axis y axis) 641mm x 400mm
Identifier: 0x43
Timestamp: 19460
Subpixel: unknown
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff0022f06c2801010101
02160104b5402878e28d85ad4f35b125
0e505400000001010101010101010101
010101010101e26800a0a0402e603020
360081902100001abc1b00a050201730
3020360081902100001a000000fc0048
50205a523330770a20202020000000ff
00434e34323032313338460a2020007b
force_audio: 0 (0x00000000) range: (-1,1)
2560x1600 (0x44) 268.5MHz +HSync -VSync *current +preferred
h: width 2560 start 2608 end 2640 total 2720 skew 0 clock
98.7KHz
v: height 1600 start 1603 end 1609 total 1646 clock
60.0Hz
1280x800 (0x45) 71.0MHz +HSync -VSync
h: width 1280 start 1328 end 1360 total 1440 skew 0 clock
49.3KHz
v: height 800 start 803 end 809 total 823 clock
59.9Hz
John Floren
2012-10-23 15:54:44 UTC
Permalink
Everybody, PLEASE, restrain yourselves and send the EDID output to Ron
directly, not to 9fans.


John
Post by ron minnich
xrandr --verbose
and send the output to me, subject
EDID
I would NOT be forever in your debt, and I will NOT put your name in
lights, but I would appreciate it :-)
ron
ron minnich
2012-10-23 18:07:55 UTC
Permalink
Post by John Floren
Everybody, PLEASE, restrain yourselves and send the EDID output to Ron
directly, not to 9fans.
Yes, good point. Also please send with subject
EDID

and you can send the text inline, not as an attachment, thanks

ron

Eugene Gorodinsky
2012-10-23 15:50:36 UTC
Permalink
This is a Vaio VGN-CR510E:

Screen 0: minimum 320 x 200, current 1280 x 800, maximum 8192 x 8192
LVDS1 connected 1280x800+0+0 (0x44) normal (normal left inverted right x
axis y axis) 0mm x 0mm
Identifier: 0x41
Timestamp: 11047
Subpixel: horizontal rgb
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 1
CRTCs: 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BACKLIGHT: 8 (0x00000008) range: (0,8)
Backlight: 8 (0x00000008) range: (0,8)
scaling mode: Full aspect
supported: None Full Center Full aspect
1280x800 (0x44) 71.1MHz -HSync -VSync *current +preferred
h: width 1280 start 1292 end 1340 total 1440 skew 0 clock
49.4KHz
v: height 800 start 804 end 807 total 823 clock
60.0Hz
1024x768 (0x45) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock
48.4KHz
v: height 768 start 771 end 777 total 806 clock
60.0Hz
800x600 (0x46) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock
37.9KHz
v: height 600 start 601 end 605 total 628 clock
60.3Hz
800x600 (0x47) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock
35.2KHz
v: height 600 start 601 end 603 total 625 clock
56.2Hz
640x480 (0x48) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock
31.5KHz
v: height 480 start 490 end 492 total 525 clock
59.9Hz
VGA1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x42
Timestamp: 11047
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
TV1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x43
Timestamp: 11047
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
bottom margin: 37 (0x00000025) range: (0,100)
right margin: 46 (0x0000002e) range: (0,100)
top margin: 36 (0x00000024) range: (0,100)
left margin: 54 (0x00000036) range: (0,100)
mode: NTSC-M
supported: NTSC-M NTSC-443 NTSC-J PAL-M
Post by ron minnich
xrandr --verbose
and send the output to me, subject
EDID
I would NOT be forever in your debt, and I will NOT put your name in
lights, but I would appreciate it :-)
ron
Loading...